The SG320-S series solar pump inverter ( also can Solar Pump VFD) is a green energy products with new solar MPPT technology, which developed based on SD800 series motor VFD, focusing on driving 3 phase AC pumps including AC induction pumps or high efficiency pumps with permanent magnet synchronous motor (PMSM) technology.
Compare to on grid or off grid solar inverter, it has soft starter, and multiple functions of motor protection, and very high competitive price.
Built in with IP54 protection grade, uses the PV350 and PV800 hardware design, all electrical components are sealed in one enclosure for water proof purpose.
With excellent in anti-dust, water proof, anti-grease and anti-corrosion properties, this inverter can using in outdoor without waterproof cabinet.
Hardware enhanced features as following:
1. Ti ‘s 32 bit DSP ( 28034/35), Germany Infineon intelligent modules;
2. Sealed cabinet, conformal coating on PCB;
3. Adopt using aviation plugs that have good quality water proof, gas and oil proof. (options)
4. Imported high-speed ventilation fan with 24V DC power supply, good cooling effect;
5. Lower failure rate and long service life.
Software updated with MPPT design based on following solar inverter, ABB, Danfoss, Delta, Lorentz, INVT,
Control mode: VF, vectorization VF, senorless vector control 1, sensorless vector control 2
MPPT function: INC and P&Q MPPT mathes.
CVT: When sunlight is good, can select CVT control for excellent stable frequency output.
Dry run function: When little water or no water for pumping to protect pumps.
Maximum current protection: set maximum current protection is available
Minimum solar input power: When low power input, inverter no work
Stop frequency: Lower than stop frequency, inverter no work
Sleep mode: if lower than sleep voltage, inverter go to sleep, it will wake up when DC voltage rise.
Flow and generated energy calculating and monitoring
A lot of fault protection. Short circuit, ground short circuit, phase loss, over current, overheat…
Built in RS485 interface, it is easy to connect GPRS remote controller.
Solar pump system constitution.
Solar pump system include solar panels arrays, solar pump inverter and AC 1/3 phase pumps, and other accessories, such as combiner box, DC circuit breaker, AC/DC manual switchover, AC circuit breaker....
System wiring diagram including solar panels, solar pump inverter and pumps.
|** Specification of Solar pump inverter specification when parameters H9.00 set to for 1.|
|Recommended MPPT voltage range||Vmp 260 to 355VDC for 2T ( For driving 220VAC pumps )Vmp 486 to 650 VDC for 4T (For driving 380VAC pumps)|
|Recommended input Voc and Vmpp voltage||Voc184(VDC), Vmp 156(VDC) for 1T modles or 110VAC pumps (Min DC is 70VDC)Voc 355(VDC), Vmp 310(VDC) for 2T model or 220V AC pumpsVoc 620(VDC), Vmp 540(VDC) for 4T model or 380V AC pumps|
|Motor(pump) type||1. Permanent magnet synchronous motor (PMSM )2. Asynchronous motor pumps ( all type 3 phase induction motor)|
|Rated output voltage||3-Phase,110V/160V/220V. 3-phase, 220V/380V/460V|
|Output frequency range||0~Maximum frequency 400Hz.|
|Efficiency||99.2 to 99.6%|
|Over load capacity||G type for submersible pumps, 150% rated current for 60s, 180% rated current for 3s P type for surface pump, 120% rated current for 60s, 150% rated current for 2s.|
|Solar pump control special performance||MPPT ( maximum power point tracking),auto/manual operation, dry run protection, low stop frequency protection, minimum power input, motor maximum current protection, flow calculating, energy generated calculating and water tank level detected.|
|Protection function||Phase loss protection, phase short circuit protection, ground to phase circuit protection , input and output short circuit protection. Stall protection, lightning protection, over heat protection.|
|Protection degree||IP20, Air force cooling|
|Running mode||MPPT or CVT|
|Altitude||Below 1000m; above 1000m, derated 1% for every additional 100m.|
|StandardAC input backup circuit||CE, Design based on AD800 series high performance inverter, more specification please refer to AD800 series vector control inverter operation manual|
PSD solar pump inveter model list
|SG320-SIP54, 2T series, 150 to 450 VDC or 220VAC input, Vmp 310VDC, 372VDC|
|1||SG320-S-2T0.75GB||4A||0-220V||0.75KW||265*180*210||260 to 355||2|
|2||SG320-S-2T1.5GB||7A||0-220V||1.5KW||265*180*210||260 to 355||2|
|3||SG320-S-2T2.2GB||10A||0-220V||2.2kw||265*180*210||260 to 375||2|
|4||SG320-S-2T3.7GB||16A||0-220V||3.7kw||335*225*245||260 to 355||3|
|SG320-SIP54, 4T series, 250 to 800 VDC or 380VAC, Vmp540VDC, Voc 648VDC|
|4||SG320-S-4T0.75GB||2.5A||0-440V||0.75KW||265*180*210||486 to 650||2|
|5||SG320-S-4T1.5GB||3.7A||0-440V||1.5KW||265*180*210||486 to 650||2|
|6||SG320-S-4T2.2GB||5A||0-440V||2.2KW||265*180*210||486 to 650||2|
|7||SG320-S-4T3.7GB||10A||0-440V||3.7KW||265*180*210||486 to 650||2|
|8||SG320-S-4T5.5GB||13A||0-440V||5.5KW||400*270*290||486 to 650||4.3|
|9||SG320-S-4T7.5GB||16A||0-440V||7.5KW||400*270*290||486 to 650||4.5|
|10||SG320-S-4T11GB||25A||0-440V||11KW||440*330*310||486 to 650||6.5|
|11||SG320-S-4T15GB||32A||0-440V||15KW||440*330*310||486 to 650||7|
|12||SG320-S-4T18.5G||38A||0-440V||18.5KW||540*400*365||486 to 650||10|
|13||SG320-S-4T22GB||45A||0-440V||22KW||540*400*365||486 to 650||11|
|14||SG320-S-4T30G||60A||0-440V||30KW||540*400*365||486 to 650||14|
PSD series sealed IP54 dimensions
|External size||Installation size 1||Installation size 2||mm|
SG320-S series solar pump inverter general wiring diagram
( Dual mode manual switchover, start/stop switch, AC/DC run mode switchover, water tank float ball sensor switch, well dry run switch, and GPRS controller...)
**Forbidden connect DC power supply to P+ and PB of PV350, otherwise it will cause serious damage.
Note:1. User use a switchover S to select AC grid or solar DC power source by manual.
2. Switch on S1 to start inverter when setting on external switch control mode, P0.01=1, and P5.00=1
3. Switch on S2 when connecting AC grid, make inverter work as normal VFD. set P5.02=51.
4. Connect 2 wires of float ball sensor to X4 and COM for water tank fulling detect, when water level reach to setting, the normal open switch of sensor will turn off to stop pumping, p5.03=54
5. Connect 2 wires of float ball sensor to X5 and COM on the well for dry run protection. P5.04=55.
6. If request to connect GPRS module controller, connect Vcc to 24vdc power supply, GND to COM, Txd to Rs485+, Rsd to Rs485-.
Irrigation of land, domestic water supply, fish farming, livestock, swimming pool, fountain, drip irrigation & sprinkler,
industrial application, swimming pool…
|Low carbon economy||In-built MPPT||Pump specific protection||Remote monitoring|
|With utilization of solar pump KEWO inverters helps you in reducing your carbon footprint. Reduce CO2 releasing. Renewable solution||Maximum power point tracking ensures that you get the most power output possible from your solar panel and maximize your pump delivery throughout the day.||Inbuilt flow measurement and flow detection function. Inverter turns off in case of dry run. Built in pumps short circuit protection, maximum pumps current setting,||With the addition of optional modules you can monitor solar pump parameters from Anywhere when GPRS signal is available|
How to select solar panels?
Below table to introduce how to selection solar panels
|265w, 38Voc (Open circuit voltage), 31Vmp ( Voltage at Pmax)|
|Inverter models||Power of pump||Connection in series (PCS) (Vmp)||Connect in parallel ( Strings) Power||Total (PCS)|
|1S (110VAC)||0.75kw to 1.0kw||4 or 5 PCS||1* strings||5*1=5|
|2S (220VAC)||0.75kw to 1.5kw||10PCS||1* strings||10*1=10|
|2S (220VAC), Max 450vdc||2.2kw||11PCS||1* strings||11*1=11|
|4T(380VAC)||0.75kw to 2.2kw||18PCS||1* strings||18*1=18|
|4T(380VAC)Max 900VDC||3.7kw||20PCS||1* strings||20*1=20|
|4T(380VAC)Max 900VDC||7.5kw||20pcs||2* strings||20*2=40|